! Started logfile: /scr/pima/rv119_uvs/J1254+1141_X_dfm.log on Sun Dec 17 11:35:45 2017 float field_size field_size = 1024 float field_cell field_cell = 0.2000 float taper_size taper_size = 70.0 float freq freq = 8.36575 obs /scr/pima/rv119_uvs/J1254+1141_X_uva.fits ! Reading UV FITS file: /scr/pima/rv119_uvs/J1254+1141_X_uva.fits ! AN table 1: 24 integrations on 66 of 66 possible baselines. ! AN table 2: 78 integrations on 15 of 15 possible baselines. ! Apparent sampling: 0.222585 visibilities/baseline/integration-bin. ! *** This seems a bit low - see "help observe" on the binwid argument. ! Found source: J1254+1141 ! ! There are 4 IFs, and a total of 4 channels: ! ! IF Channel Frequency Freq offset Number of Overall IF ! origin at origin per channel channels bandwidth ! ------------------------------------------------------------- (Hz) ! 01 1 8.36575e+09 8e+06 1 8e+06 ! 02 2 8.44575e+09 8e+06 1 8e+06 ! 03 3 8.80575e+09 8e+06 1 8e+06 ! 04 4 8.92575e+09 8e+06 1 8e+06 ! ! Polarization(s): RR ! ! Read 79 lines of history. ! ! Reading 2452 visibilities. select rr, 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16 ! Restricting channel ranges to the available 4 channels. ! Selecting polarization: RR, channels: 1..4 ! Reading IF 1 channels: 1..1 ! Reading IF 2 channels: 2..2 ! Reading IF 3 channels: 3..3 ! Reading IF 4 channels: 4..4 print "field_size =", field_size ! field_size = 1024 print "field_cell =", field_cell ! field_cell = 0.2 print "taper_size =", taper_size ! taper_size = 70 ![@/opt64/bin/pima_mupet_01.dfm J1254+1141_X] float lim_self lim_self = 120.0 float lim_val lim_va = 1.2 integer clean_niter clean_niter = 100 float clean_gain clean_gain = 0.03 float dynam dynam = 6.0 float soltime1 soltime1 = 120 float soltime2 soltime2 = 20 float thresh thresh = 0.5 float win_mult win_mult = 1.8 float time_av time_av = 16 float old_peak float new_peak float flux_cutoff mapsize field_size, field_cell ! Map grid = 1024x1024 pixels with 0.200x0.200 milli-arcsec cellsize. startmod ! Applying default point source starting model. ! Performing phase self-cal ! Adding 1 model components to the UV plane model. ! The established model now contains 1 components and 1 Jy ! ! Correcting IF 1. ! A total of 208 telescope corrections were flagged in sub-array 1. ! A total of 334 telescope corrections were flagged in sub-array 2. ! ! Correcting IF 2. ! A total of 208 telescope corrections were flagged in sub-array 1. ! A total of 334 telescope corrections were flagged in sub-array 2. ! ! Correcting IF 3. ! A total of 208 telescope corrections were flagged in sub-array 1. ! A total of 334 telescope corrections were flagged in sub-array 2. ! ! Correcting IF 4. ! A total of 208 telescope corrections were flagged in sub-array 1. ! A total of 334 telescope corrections were flagged in sub-array 2. ! ! Fit before self-cal, rms=1.151986Jy sigma=15.001886 ! Fit after self-cal, rms=0.469256Jy sigma=6.165262 ! clrmod: Cleared the established, tentative and continuum models. ! Redundant starting model cleared. uvw 2,-1 ! Uniform weighting binwidth: 2 (pixels). ! Gridding weights will be scaled by errors raised to the power -1. ! Radial weighting is not currently selected. flux_cutoff = imstat(rms) * dynam ! Inverting map and beam ! Your choice of large map pixels excluded 8.02% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1765 milli-arcsec ! Estimated beam: bmin=0.6839 mas, bmaj=0.9482 mas, bpa=-24.22 degrees ! Estimated noise=1.68511 mJy/beam. repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! Added new window around map position (0, 0). ! clean: niter=100 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.416647 Jy ! Component: 100 - total flux cleaned = 0.538143 Jy ! Total flux subtracted in 100 components = 0.538143 Jy ! Clean residual min=-0.024238 max=0.061998 Jy/beam ! Clean residual mean=0.000170 rms=0.005857 Jy/beam ! Combined flux in latest and established models = 0.538143 Jy ! Performing phase self-cal ! Adding 6 model components to the UV plane model. ! The established model now contains 6 components and 0.538143 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.197386Jy sigma=1.980971 ! Fit after self-cal, rms=0.196660Jy sigma=1.977187 ! Inverting map ! Your choice of large map pixels excluded 8.02% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1765 milli-arcsec ! Added new window around map position (-1.8, -0.4). ! clean: niter=100 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.0674818 Jy ! Component: 100 - total flux cleaned = 0.108792 Jy ! Total flux subtracted in 100 components = 0.108792 Jy ! Clean residual min=-0.019746 max=0.033833 Jy/beam ! Clean residual mean=0.000072 rms=0.003973 Jy/beam ! Combined flux in latest and established models = 0.646935 Jy ! Performing phase self-cal ! Adding 14 model components to the UV plane model. ! The established model now contains 14 components and 0.646935 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.164632Jy sigma=1.458754 ! Fit after self-cal, rms=0.162141Jy sigma=1.431899 ! Inverting map ! Your choice of large map pixels excluded 8.02% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1765 milli-arcsec ! clean: niter=100 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.0288248 Jy ! Component: 100 - total flux cleaned = 0.0349293 Jy ! Total flux subtracted in 100 components = 0.0349293 Jy ! Clean residual min=-0.015988 max=0.021924 Jy/beam ! Clean residual mean=0.000041 rms=0.003307 Jy/beam ! Combined flux in latest and established models = 0.681865 Jy ! Performing phase self-cal ! Adding 14 model components to the UV plane model. ! The established model now contains 18 components and 0.681865 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.149757Jy sigma=1.286281 ! Fit after self-cal, rms=0.148878Jy sigma=1.277265 ! Inverting map ! Your choice of large map pixels excluded 8.02% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1765 milli-arcsec ! clean: niter=100 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00895775 Jy ! Component: 100 - total flux cleaned = 0.0105561 Jy ! Total flux subtracted in 100 components = 0.0105561 Jy ! Clean residual min=-0.014133 max=0.017038 Jy/beam ! Clean residual mean=0.000031 rms=0.003006 Jy/beam ! Combined flux in latest and established models = 0.692421 Jy ! Performing phase self-cal ! Adding 11 model components to the UV plane model. ! The established model now contains 19 components and 0.692421 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.140080Jy sigma=1.208473 ! Fit after self-cal, rms=0.139771Jy sigma=1.206392 ! Inverting map ! Your choice of large map pixels excluded 8.02% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1765 milli-arcsec print "************** FINISHED UNIFORM WEIGHTING CLEAN **************" ! ************** FINISHED UNIFORM WEIGHTING CLEAN ************** ! uvw 0,-1 ! Uniform weighting is not currently selected. ! Gridding weights will be scaled by errors raised to the power -1. ! Radial weighting is not currently selected. win_mult = win_mult * 1.6 clean_niter = clean_niter * 2 dynam = dynam - 0.5 flux_cutoff = imstat(rms) * dynam ! Inverting map and beam ! Your choice of large map pixels excluded 8.02% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1765 milli-arcsec ! Estimated beam: bmin=0.7793 mas, bmaj=1.004 mas, bpa=-27.79 degrees ! Estimated noise=1.31807 mJy/beam. repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.0192288 Jy ! Component: 100 - total flux cleaned = 0.0217241 Jy ! Component: 150 - total flux cleaned = 0.022853 Jy ! Component: 200 - total flux cleaned = 0.024398 Jy ! Total flux subtracted in 200 components = 0.024398 Jy ! Clean residual min=-0.010607 max=0.014176 Jy/beam ! Clean residual mean=0.000003 rms=0.002477 Jy/beam ! Combined flux in latest and established models = 0.716819 Jy ! Performing phase self-cal ! Adding 16 model components to the UV plane model. ! The established model now contains 25 components and 0.716819 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.128819Jy sigma=1.127300 ! Fit after self-cal, rms=0.128540Jy sigma=1.124949 ! Inverting map ! Your choice of large map pixels excluded 8.02% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1765 milli-arcsec print "************** FINISHED NATURAL WEIGHTING CLEAN **************" ! ************** FINISHED NATURAL WEIGHTING CLEAN ************** ! restore ! restore: Substituting estimate of restoring beam from last 'invert'. ! Restoring with beam: 0.7793 x 1.004 at -27.79 degrees (North through East) ! Clean map min=-0.0085182 max=0.5295 Jy/beam gscale true ! Performing overall amplitude self-cal ! ! Correcting IF 1. ! A total of 6 telescope corrections were flagged in sub-array 1. ! Telescope amplitude corrections in sub-array 1: ! BR 1.00 FD 1.00* HN 0.99 KP 0.99 ! LA 1.00 MK 1.03 NL 1.01 NY 1.05 ! ON 0.99 OV 1.03 PT 1.00 SC 1.01 ! ! A total of 78 telescope corrections were flagged in sub-array 2. ! Telescope amplitude corrections in sub-array 2: ! HH 0.76 HN 1.19 NY 1.00 ON 0.96 ! SC 1.01 WZ 0.98 ! ! ! Correcting IF 2. ! A total of 6 telescope corrections were flagged in sub-array 1. ! Telescope amplitude corrections in sub-array 1: ! BR 0.99 FD 1.00* HN 1.01 KP 1.01 ! LA 0.99 MK 1.02 NL 0.99 NY 1.00 ! ON 1.01 OV 1.01 PT 1.01 SC 1.00 ! ! A total of 78 telescope corrections were flagged in sub-array 2. ! Telescope amplitude corrections in sub-array 2: ! HH 0.78 HN 1.29 NY 0.97 ON 0.96 ! SC 1.03 WZ 0.98 ! ! ! Correcting IF 3. ! A total of 6 telescope corrections were flagged in sub-array 1. ! Telescope amplitude corrections in sub-array 1: ! BR 1.02 FD 1.00* HN 1.00 KP 0.98 ! LA 1.00 MK 0.99 NL 1.00 NY 1.12 ! ON 1.06 OV 0.99 PT 0.97 SC 0.98 ! ! A total of 78 telescope corrections were flagged in sub-array 2. ! Telescope amplitude corrections in sub-array 2: ! HH 0.81 HN 1.20 NY 1.03 ON 1.00 ! SC 1.01 WZ 0.93 ! ! ! Correcting IF 4. ! A total of 6 telescope corrections were flagged in sub-array 1. ! Telescope amplitude corrections in sub-array 1: ! BR 1.03 FD 1.00* HN 0.97 KP 0.99 ! LA 0.99 MK 0.99 NL 0.97 NY 1.00 ! ON 1.02 OV 1.00 PT 1.00 SC 0.94 ! ! A total of 78 telescope corrections were flagged in sub-array 2. ! Telescope amplitude corrections in sub-array 2: ! HH 0.98 HN 1.09 NY 0.97 ON 0.99 ! SC 1.01 WZ 0.96 ! ! ! Fit before self-cal, rms=0.128540Jy sigma=1.124949 ! Fit after self-cal, rms=0.090485Jy sigma=0.972560 dynam = dynam - 0.5 flux_cutoff = imstat(rms) * dynam ! Inverting map and beam ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Estimated beam: bmin=0.7797 mas, bmaj=1.018 mas, bpa=-18.99 degrees ! Estimated noise=1.32685 mJy/beam. repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00261809 Jy ! Component: 100 - total flux cleaned = 0.00148858 Jy ! Component: 150 - total flux cleaned = 0.000587221 Jy ! Component: 200 - total flux cleaned = -2.15057e-05 Jy ! Total flux subtracted in 200 components = -2.15057e-05 Jy ! Clean residual min=-0.006765 max=0.006076 Jy/beam ! Clean residual mean=0.000001 rms=0.001453 Jy/beam ! Combined flux in latest and established models = 0.716797 Jy ! Performing phase self-cal ! Adding 6 model components to the UV plane model. ! The established model now contains 31 components and 0.716797 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.089096Jy sigma=0.953390 ! Fit after self-cal, rms=0.088720Jy sigma=0.950782 ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec selfcal true, true, soltime1 ! Performing amp+phase self-cal over 120 minute time intervals ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.088720Jy sigma=0.950782 ! Fit after self-cal, rms=0.087414Jy sigma=0.923972 dynam = dynam - 0.75 clean clean_niter,clean_gain ! Inverting map and beam ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Estimated beam: bmin=0.7793 mas, bmaj=1.014 mas, bpa=-18.83 degrees ! Estimated noise=1.32584 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.000369953 Jy ! Component: 100 - total flux cleaned = -0.000273277 Jy ! Component: 150 - total flux cleaned = -0.000678111 Jy ! Component: 200 - total flux cleaned = -0.000903583 Jy ! Total flux subtracted in 200 components = -0.000903583 Jy ! Clean residual min=-0.005581 max=0.005131 Jy/beam ! Clean residual mean=0.000003 rms=0.001266 Jy/beam ! Combined flux in latest and established models = 0.715894 Jy selfcal ! Performing phase self-cal ! Adding 7 model components to the UV plane model. ! The established model now contains 34 components and 0.715894 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.086762Jy sigma=0.916573 ! Fit after self-cal, rms=0.086653Jy sigma=0.915882 flux_cutoff = imstat(rms) * dynam ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.000313682 Jy ! Component: 100 - total flux cleaned = 0.000315842 Jy ! Component: 150 - total flux cleaned = 0.000413068 Jy ! Component: 200 - total flux cleaned = 0.000498575 Jy ! Total flux subtracted in 200 components = 0.000498575 Jy ! Clean residual min=-0.005312 max=0.005181 Jy/beam ! Clean residual mean=0.000003 rms=0.001250 Jy/beam ! Combined flux in latest and established models = 0.716392 Jy ! Performing phase self-cal ! Adding 11 model components to the UV plane model. ! The established model now contains 39 components and 0.716392 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.086408Jy sigma=0.913243 ! Fit after self-cal, rms=0.086344Jy sigma=0.913001 ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec selfcal true, true, soltime2 ! Performing amp+phase self-cal over 20 minute time intervals ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.086344Jy sigma=0.913001 ! Fit after self-cal, rms=0.085655Jy sigma=0.906582 clean clean_niter,clean_gain ! Inverting map and beam ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Estimated beam: bmin=0.7799 mas, bmaj=1.011 mas, bpa=-18.84 degrees ! Estimated noise=1.32492 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = -0.000410659 Jy ! Component: 100 - total flux cleaned = -0.00050574 Jy ! Component: 150 - total flux cleaned = -0.000504834 Jy ! Component: 200 - total flux cleaned = -0.000426357 Jy ! Total flux subtracted in 200 components = -0.000426357 Jy ! Clean residual min=-0.004860 max=0.005083 Jy/beam ! Clean residual mean=0.000007 rms=0.001154 Jy/beam ! Combined flux in latest and established models = 0.715966 Jy selfcal ! Performing phase self-cal ! Adding 10 model components to the UV plane model. ! The established model now contains 40 components and 0.715966 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.085409Jy sigma=0.904102 ! Fit after self-cal, rms=0.085369Jy sigma=0.903891 flux_cutoff = imstat(rms) * dynam ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! Added new window around map position (51, 37.2). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00270615 Jy ! Component: 100 - total flux cleaned = 0.0030242 Jy ! Component: 150 - total flux cleaned = 0.00310715 Jy ! Component: 200 - total flux cleaned = 0.00317997 Jy ! Total flux subtracted in 200 components = 0.00317997 Jy ! Clean residual min=-0.004870 max=0.004884 Jy/beam ! Clean residual mean=0.000007 rms=0.001127 Jy/beam ! Combined flux in latest and established models = 0.719146 Jy ! Performing phase self-cal ! Adding 18 model components to the UV plane model. ! The established model now contains 49 components and 0.719146 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.085009Jy sigma=0.900415 ! Fit after self-cal, rms=0.084983Jy sigma=0.900079 ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec uvtaper 0.3,taper_size ! Gaussian taper: value 0.3 at UV radius = 70 mega-wavelengths. win_mult = win_mult * 1.2 selfcal true, true, soltime2 ! Performing amp+phase self-cal over 20 minute time intervals ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.084983Jy sigma=0.900079 ! Fit after self-cal, rms=0.084894Jy sigma=0.899443 clean clean_niter,clean_gain ! Inverting map and beam ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Estimated beam: bmin=2.128 mas, bmaj=2.663 mas, bpa=-18.1 degrees ! Estimated noise=1.76369 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00132751 Jy ! Component: 100 - total flux cleaned = 0.00147716 Jy ! Component: 150 - total flux cleaned = 0.00147695 Jy ! Component: 200 - total flux cleaned = 0.0015513 Jy ! Total flux subtracted in 200 components = 0.0015513 Jy ! Clean residual min=-0.005018 max=0.004863 Jy/beam ! Clean residual mean=0.000019 rms=0.001375 Jy/beam ! Combined flux in latest and established models = 0.720697 Jy selfcal ! Performing phase self-cal ! Adding 11 model components to the UV plane model. ! The established model now contains 58 components and 0.720697 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.084920Jy sigma=0.899563 ! Fit after self-cal, rms=0.084899Jy sigma=0.899365 flux_cutoff = imstat(rms) * dynam ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.000331591 Jy ! Component: 100 - total flux cleaned = 0.000480436 Jy ! Component: 150 - total flux cleaned = 0.000573253 Jy ! Component: 200 - total flux cleaned = 0.000678884 Jy ! Total flux subtracted in 200 components = 0.000678884 Jy ! Clean residual min=-0.004955 max=0.004820 Jy/beam ! Clean residual mean=0.000018 rms=0.001363 Jy/beam ! Combined flux in latest and established models = 0.721376 Jy ! Performing phase self-cal ! Adding 16 model components to the UV plane model. ! The established model now contains 69 components and 0.721376 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.084909Jy sigma=0.899630 ! Fit after self-cal, rms=0.084898Jy sigma=0.899550 ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec uvtaper 0,0 ! No UV-taper is currently set. win_mult = win_mult / 1.2 print "************** FINISHED AMPLITUDE SELF-CAL **************" ! ************** FINISHED AMPLITUDE SELF-CAL ************** restore ! Inverting map and beam ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Estimated beam: bmin=0.7805 mas, bmaj=1.01 mas, bpa=-18.89 degrees ! Estimated noise=1.32421 mJy/beam. ! restore: Substituting estimate of restoring beam from last 'invert'. ! Restoring with beam: 0.7805 x 1.01 at -18.89 degrees (North through East) ! Clean map min=-0.0040833 max=0.52236 Jy/beam if(peak(flux) > thresh) selfcal true, true clean clean_niter,clean_gain selfcal flux_cutoff = imstat(rms) * dynam repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) selfcal true, true end if ! Performing amp+phase self-cal ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.084898Jy sigma=0.899550 ! Fit after self-cal, rms=0.079033Jy sigma=0.819339 ! Inverting map and beam ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Estimated beam: bmin=0.7805 mas, bmaj=1.009 mas, bpa=-18.87 degrees ! Estimated noise=1.32337 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = -0.000839131 Jy ! Component: 100 - total flux cleaned = -0.000925924 Jy ! Component: 150 - total flux cleaned = -0.000853595 Jy ! Component: 200 - total flux cleaned = -0.000785941 Jy ! Total flux subtracted in 200 components = -0.000785941 Jy ! Clean residual min=-0.004612 max=0.004825 Jy/beam ! Clean residual mean=0.000005 rms=0.001106 Jy/beam ! Combined flux in latest and established models = 0.72059 Jy ! Performing phase self-cal ! Adding 16 model components to the UV plane model. ! The established model now contains 74 components and 0.72059 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.078832Jy sigma=0.817843 ! Fit after self-cal, rms=0.078813Jy sigma=0.817760 ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Added new window around map position (-11.2, -36.2). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00322721 Jy ! Component: 100 - total flux cleaned = 0.00368228 Jy ! Component: 150 - total flux cleaned = 0.00367846 Jy ! Component: 200 - total flux cleaned = 0.00389462 Jy ! Total flux subtracted in 200 components = 0.00389462 Jy ! Clean residual min=-0.004812 max=0.004602 Jy/beam ! Clean residual mean=0.000004 rms=0.001083 Jy/beam ! Combined flux in latest and established models = 0.724485 Jy ! Performing phase self-cal ! Adding 21 model components to the UV plane model. ! The established model now contains 87 components and 0.724485 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.078446Jy sigma=0.813952 ! Fit after self-cal, rms=0.078416Jy sigma=0.813729 ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Performing amp+phase self-cal ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.078416Jy sigma=0.813729 ! Fit after self-cal, rms=0.078409Jy sigma=0.813267 print "************** CLEARING MODEL AND STARTING OVER **********" ! ************** CLEARING MODEL AND STARTING OVER ********** clrmod true ! clrmod: Cleared the established and tentative models. uvw 2,-1 ! Uniform weighting binwidth: 2 (pixels). ! Gridding weights will be scaled by errors raised to the power -1. ! Radial weighting is not currently selected. clean clean_niter,clean_gain ! Inverting map and beam ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Estimated beam: bmin=0.691 mas, bmaj=0.9665 mas, bpa=-18.54 degrees ! Estimated noise=1.6894 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.411462 Jy ! Component: 100 - total flux cleaned = 0.538037 Jy ! Component: 150 - total flux cleaned = 0.606369 Jy ! Component: 200 - total flux cleaned = 0.646267 Jy ! Total flux subtracted in 200 components = 0.646267 Jy ! Clean residual min=-0.011023 max=0.020744 Jy/beam ! Clean residual mean=0.000075 rms=0.002649 Jy/beam ! Combined flux in latest and established models = 0.646267 Jy uvw 0,-1 ! Uniform weighting is not currently selected. ! Gridding weights will be scaled by errors raised to the power -1. ! Radial weighting is not currently selected. flux_cutoff = imstat(rms) * dynam ! Adding 10 model components to the UV plane model. ! The established model now contains 10 components and 0.646267 Jy ! Inverting map and beam ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Estimated beam: bmin=0.7812 mas, bmaj=1.008 mas, bpa=-18.89 degrees ! Estimated noise=1.3227 mJy/beam. repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam keep new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.0297564 Jy ! Component: 100 - total flux cleaned = 0.0473694 Jy ! Component: 150 - total flux cleaned = 0.0583089 Jy ! Component: 200 - total flux cleaned = 0.0647508 Jy ! Total flux subtracted in 200 components = 0.0647508 Jy ! Clean residual min=-0.006092 max=0.006580 Jy/beam ! Clean residual mean=0.000011 rms=0.001337 Jy/beam ! Combined flux in latest and established models = 0.711018 Jy ! Adding 22 model components to the UV plane model. ! The established model now contains 25 components and 0.711018 Jy ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Added new window around map position (1.8, -0.6). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00216214 Jy ! Component: 100 - total flux cleaned = 0.00399764 Jy ! Component: 150 - total flux cleaned = 0.00566811 Jy ! Component: 200 - total flux cleaned = 0.00654029 Jy ! Total flux subtracted in 200 components = 0.00654029 Jy ! Clean residual min=-0.005194 max=0.005231 Jy/beam ! Clean residual mean=0.000007 rms=0.001201 Jy/beam ! Combined flux in latest and established models = 0.717558 Jy ! Adding 19 model components to the UV plane model. ! The established model now contains 36 components and 0.717558 Jy ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Added new window around map position (-10.2, 31.8). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00263177 Jy ! Component: 100 - total flux cleaned = 0.00319963 Jy ! Component: 150 - total flux cleaned = 0.00391477 Jy ! Component: 200 - total flux cleaned = 0.00473695 Jy ! Total flux subtracted in 200 components = 0.00473695 Jy ! Clean residual min=-0.004700 max=0.004895 Jy/beam ! Clean residual mean=0.000005 rms=0.001124 Jy/beam ! Combined flux in latest and established models = 0.722295 Jy ! Adding 24 model components to the UV plane model. ! The established model now contains 42 components and 0.722295 Jy ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Added new window around map position (3.8, 41.6). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00238197 Jy ! Component: 100 - total flux cleaned = 0.00283733 Jy ! Component: 150 - total flux cleaned = 0.00340003 Jy ! Component: 200 - total flux cleaned = 0.00393012 Jy ! Total flux subtracted in 200 components = 0.00393012 Jy ! Clean residual min=-0.004454 max=0.004599 Jy/beam ! Clean residual mean=0.000003 rms=0.001071 Jy/beam ! Combined flux in latest and established models = 0.726225 Jy ! Adding 25 model components to the UV plane model. ! The established model now contains 47 components and 0.726225 Jy ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Added new window around map position (-7, -16.6). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00220885 Jy ! Component: 100 - total flux cleaned = 0.00296492 Jy ! Component: 150 - total flux cleaned = 0.00355571 Jy ! Component: 200 - total flux cleaned = 0.00411638 Jy ! Total flux subtracted in 200 components = 0.00411638 Jy ! Clean residual min=-0.004232 max=0.004412 Jy/beam ! Clean residual mean=0.000003 rms=0.001033 Jy/beam ! Combined flux in latest and established models = 0.730342 Jy ! Adding 34 model components to the UV plane model. ! The established model now contains 62 components and 0.730342 Jy ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Added new window around map position (0, -35.2). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00262087 Jy ! Component: 100 - total flux cleaned = 0.002943 Jy ! Component: 150 - total flux cleaned = 0.00304002 Jy ! Component: 200 - total flux cleaned = 0.00303757 Jy ! Total flux subtracted in 200 components = 0.00303757 Jy ! Clean residual min=-0.004292 max=0.004335 Jy/beam ! Clean residual mean=0.000000 rms=0.001009 Jy/beam ! Combined flux in latest and established models = 0.733379 Jy ! Adding 35 model components to the UV plane model. ! The established model now contains 73 components and 0.73338 Jy ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Added new window around map position (-34, -24.6). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00253209 Jy ! Component: 100 - total flux cleaned = 0.00427397 Jy ! Component: 150 - total flux cleaned = 0.00484432 Jy ! Component: 200 - total flux cleaned = 0.00547595 Jy ! Total flux subtracted in 200 components = 0.00547595 Jy ! Clean residual min=-0.004120 max=0.004042 Jy/beam ! Clean residual mean=0.000003 rms=0.000980 Jy/beam ! Combined flux in latest and established models = 0.738855 Jy ! Adding 33 model components to the UV plane model. ! The established model now contains 89 components and 0.738856 Jy ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec uvtaper 0.3,taper_size ! Gaussian taper: value 0.3 at UV radius = 70 mega-wavelengths. clean clean_niter,clean_gain ! Inverting map and beam ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Estimated beam: bmin=2.129 mas, bmaj=2.664 mas, bpa=-18.17 degrees ! Estimated noise=1.75943 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00120774 Jy ! Component: 100 - total flux cleaned = 0.00179565 Jy ! Component: 150 - total flux cleaned = 0.00235013 Jy ! Component: 200 - total flux cleaned = 0.00267247 Jy ! Total flux subtracted in 200 components = 0.00267247 Jy ! Clean residual min=-0.003866 max=0.003333 Jy/beam ! Clean residual mean=0.000004 rms=0.001050 Jy/beam ! Combined flux in latest and established models = 0.741528 Jy flux_cutoff = imstat(rms) * dynam repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam keep new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.000196273 Jy ! Component: 100 - total flux cleaned = 0.000421294 Jy ! Component: 150 - total flux cleaned = 0.00042109 Jy ! Component: 200 - total flux cleaned = 0.000459463 Jy ! Total flux subtracted in 200 components = 0.000459463 Jy ! Clean residual min=-0.003737 max=0.003369 Jy/beam ! Clean residual mean=0.000002 rms=0.001032 Jy/beam ! Combined flux in latest and established models = 0.741987 Jy ! Adding 35 model components to the UV plane model. ! The established model now contains 120 components and 0.741987 Jy ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec uvtaper 0,0 ! No UV-taper is currently set. clean ! Inverting map and beam ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! Estimated beam: bmin=0.7812 mas, bmaj=1.008 mas, bpa=-18.89 degrees ! Estimated noise=1.3227 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = -0.00125524 Jy ! Component: 100 - total flux cleaned = -0.00142571 Jy ! Component: 150 - total flux cleaned = -0.00142713 Jy ! Component: 200 - total flux cleaned = -0.00135194 Jy ! Total flux subtracted in 200 components = -0.00135194 Jy ! Clean residual min=-0.003878 max=0.004055 Jy/beam ! Clean residual mean=0.000001 rms=0.000948 Jy/beam ! Combined flux in latest and established models = 0.740636 Jy selfcal ! Performing phase self-cal ! Adding 37 model components to the UV plane model. ! The established model now contains 130 components and 0.740635 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.080989Jy sigma=0.820265 ! Fit after self-cal, rms=0.080032Jy sigma=0.815056 wmodel J1254+1141_X_map.mod ! Writing 130 model components to file: J1254+1141_X_map.mod wobs J1254+1141_X_uvs.fits ! Writing UV FITS file: J1254+1141_X_uvs.fits wwins J1254+1141_X_map.win ! wwins: Wrote 10 windows to J1254+1141_X_map.win x = (field_size-8) * field_cell / 4 addwin -x,x,-x,x clean (field_size*4),0.01 ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! clean: niter=4096 gain=0.01 cutoff=0 ! Component: 050 - total flux cleaned = 0.000966865 Jy ! Component: 100 - total flux cleaned = 0.000890254 Jy ! Component: 150 - total flux cleaned = 0.000891869 Jy ! Component: 200 - total flux cleaned = 0.000890709 Jy ! Component: 250 - total flux cleaned = 0.00102361 Jy ! Component: 300 - total flux cleaned = 0.000827053 Jy ! Component: 350 - total flux cleaned = 0.000763765 Jy ! Component: 400 - total flux cleaned = 0.000701667 Jy ! Component: 450 - total flux cleaned = 0.000763863 Jy ! Component: 500 - total flux cleaned = 0.000763945 Jy ! Component: 550 - total flux cleaned = 0.000704633 Jy ! Component: 600 - total flux cleaned = 0.000882996 Jy ! Component: 650 - total flux cleaned = 0.000999999 Jy ! Component: 700 - total flux cleaned = 0.00111538 Jy ! Component: 750 - total flux cleaned = 0.00111563 Jy ! Component: 800 - total flux cleaned = 0.00145477 Jy ! Component: 850 - total flux cleaned = 0.00151109 Jy ! Component: 900 - total flux cleaned = 0.00173244 Jy ! Component: 950 - total flux cleaned = 0.00178715 Jy ! Component: 1000 - total flux cleaned = 0.00222053 Jy ! Component: 1050 - total flux cleaned = 0.00227281 Jy ! Component: 1100 - total flux cleaned = 0.00227265 Jy ! Component: 1150 - total flux cleaned = 0.00237773 Jy ! Component: 1200 - total flux cleaned = 0.0023786 Jy ! Component: 1250 - total flux cleaned = 0.00253411 Jy ! Component: 1300 - total flux cleaned = 0.00248327 Jy ! Component: 1350 - total flux cleaned = 0.00273575 Jy ! Component: 1400 - total flux cleaned = 0.00258638 Jy ! Component: 1450 - total flux cleaned = 0.00263643 Jy ! Component: 1500 - total flux cleaned = 0.00253871 Jy ! Component: 1550 - total flux cleaned = 0.00244157 Jy ! Component: 1600 - total flux cleaned = 0.00263361 Jy ! Component: 1650 - total flux cleaned = 0.00239525 Jy ! Component: 1700 - total flux cleaned = 0.00253648 Jy ! Component: 1750 - total flux cleaned = 0.0024424 Jy ! Component: 1800 - total flux cleaned = 0.0024421 Jy ! Component: 1850 - total flux cleaned = 0.00253375 Jy ! Component: 1900 - total flux cleaned = 0.00248822 Jy ! Component: 1950 - total flux cleaned = 0.00262403 Jy ! Component: 2000 - total flux cleaned = 0.00253374 Jy ! Component: 2050 - total flux cleaned = 0.00244405 Jy ! Component: 2100 - total flux cleaned = 0.00244366 Jy ! Component: 2150 - total flux cleaned = 0.00235521 Jy ! Component: 2200 - total flux cleaned = 0.00222364 Jy ! Component: 2250 - total flux cleaned = 0.00235388 Jy ! Component: 2300 - total flux cleaned = 0.00218196 Jy ! Component: 2350 - total flux cleaned = 0.002395 Jy ! Component: 2400 - total flux cleaned = 0.00218305 Jy ! Component: 2450 - total flux cleaned = 0.00230948 Jy ! Component: 2500 - total flux cleaned = 0.00235136 Jy ! Component: 2550 - total flux cleaned = 0.00251753 Jy ! Component: 2600 - total flux cleaned = 0.00268253 Jy ! Component: 2650 - total flux cleaned = 0.00255971 Jy ! Component: 2700 - total flux cleaned = 0.00272224 Jy ! Component: 2750 - total flux cleaned = 0.0026014 Jy ! Component: 2800 - total flux cleaned = 0.00276157 Jy ! Component: 2850 - total flux cleaned = 0.00280123 Jy ! Component: 2900 - total flux cleaned = 0.00272198 Jy ! Component: 2950 - total flux cleaned = 0.00276119 Jy ! Component: 3000 - total flux cleaned = 0.00264429 Jy ! Component: 3050 - total flux cleaned = 0.00268301 Jy ! Component: 3100 - total flux cleaned = 0.00268338 Jy ! Component: 3150 - total flux cleaned = 0.00272165 Jy ! Component: 3200 - total flux cleaned = 0.00275994 Jy ! Component: 3250 - total flux cleaned = 0.00279732 Jy ! Component: 3300 - total flux cleaned = 0.00275996 Jy ! Component: 3350 - total flux cleaned = 0.00268527 Jy ! Component: 3400 - total flux cleaned = 0.00264782 Jy ! Component: 3450 - total flux cleaned = 0.00253705 Jy ! Component: 3500 - total flux cleaned = 0.00246355 Jy ! Component: 3550 - total flux cleaned = 0.00242681 Jy ! Component: 3600 - total flux cleaned = 0.00231802 Jy ! Component: 3650 - total flux cleaned = 0.00217397 Jy ! Component: 3700 - total flux cleaned = 0.00206649 Jy ! Component: 3750 - total flux cleaned = 0.00213777 Jy ! Component: 3800 - total flux cleaned = 0.00213752 Jy ! Component: 3850 - total flux cleaned = 0.00224343 Jy ! Component: 3900 - total flux cleaned = 0.00231331 Jy ! Component: 3950 - total flux cleaned = 0.00224364 Jy ! Component: 4000 - total flux cleaned = 0.00241689 Jy ! Component: 4050 - total flux cleaned = 0.00224399 Jy ! Total flux subtracted in 4096 components = 0.00241567 Jy ! Clean residual min=-0.002319 max=0.002100 Jy/beam ! Clean residual mean=0.000006 rms=0.000560 Jy/beam ! Combined flux in latest and established models = 0.743051 Jy keep ! Adding 302 model components to the UV plane model. ! The established model now contains 432 components and 0.743051 Jy ![Exited script file: /opt64/bin/pima_mupet_01.dfm] wmap /scr/pima/rv119_uvs/J1254+1141_X_map.fits ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec ! restore: Substituting estimate of restoring beam from last 'invert'. ! Restoring with beam: 0.7812 x 1.008 at -18.89 degrees (North through East) ! Clean map min=-0.0057957 max=0.51839 Jy/beam ! Writing clean map to FITS file: /scr/pima/rv119_uvs/J1254+1141_X_map.fits wmodel /scr/pima/rv119_uvs/J1254+1141_X_map.mod ! Writing 432 model components to file: /scr/pima/rv119_uvs/J1254+1141_X_map.mod wobs /scr/pima/rv119_uvs/J1254+1141_X_uvs.fits ! Writing UV FITS file: /scr/pima/rv119_uvs/J1254+1141_X_uvs.fits wwins /scr/pima/rv119_uvs/J1254+1141_X_map.win ! wwins: Wrote 11 windows to /scr/pima/rv119_uvs/J1254+1141_X_map.win float peak_flux peak_flux = peak(flux,max) print "The peak flux is", peak_flux ! The peak flux is 0.518393 invert ! Inverting map ! Your choice of large map pixels excluded 4.1% of the data. ! The x-axis pixel size should ideally be below 0.1844 milli-arcsec ! The y-axis pixel size should ideally be below 0.1766 milli-arcsec float image_rms image_rms = imstat(rms) print "The final image rms is",image_rms ! The final image rms is 0.000556967 loglevs 100*3*image_rms/peak_flux ! The new contour levels are: ! -0.322323 0.322323 0.644646 1.28929 2.57859 5.15717 10.3143 20.6287 41.2574 82.5147 print "clev= ", int(3*image_rms*10000)/10000 ! clev= 0.0016 print "peak= ", int(1000*peak_flux)/1000 ! peak= 0.518 print "dyn_range= ", int(1000*peak_flux/image_rms)/1000 ! dyn_range= 930.742 quit ! Quitting program ! Log file /scr/pima/rv119_uvs/J1254+1141_X_dfm.log closed on Sun Dec 17 11:35:50 2017