! Started logfile: /scr/pima/rv102_uvs/J0927-2034_X_dfm.log on Sat Nov 9 10:18:33 2019 float field_size field_size = 1024 float field_cell field_cell = 0.2000 float taper_size taper_size = 70.0 float freq freq = 8.40599 obs /scr/pima/rv102_uvs/J0927-2034_X_uva.fits ! Reading UV FITS file: /scr/pima/rv102_uvs/J0927-2034_X_uva.fits ! AN table 1: 303 integrations on 3 of 3 possible baselines. ! AN table 2: 34 integrations on 6 of 6 possible baselines. ! AN table 3: 13 integrations on 3 of 3 possible baselines. ! AN table 4: 21 integrations on 3 of 3 possible baselines. ! AN table 5: 9 integrations on 1 of 1 possible baselines. ! AN table 6: 9 integrations on 6 of 6 possible baselines. ! AN table 7: 27 integrations on 28 of 28 possible baselines. ! AN table 8: 9 integrations on 6 of 6 possible baselines. ! AN table 9: 9 integrations on 36 of 36 possible baselines. ! AN table 10: 9 integrations on 3 of 3 possible baselines. ! AN table 11: 9 integrations on 28 of 28 possible baselines. ! AN table 12: 9 integrations on 1 of 1 possible baselines. ! AN table 13: 9 integrations on 3 of 3 possible baselines. ! Apparent sampling: 0.903924 visibilities/baseline/integration-bin. ! Found source: J0927-2034 ! ! There are 4 IFs, and a total of 4 channels: ! ! IF Channel Frequency Freq offset Number of Overall IF ! origin at origin per channel channels bandwidth ! ------------------------------------------------------------- (Hz) ! 01 1 8.40599e+09 8e+06 1 8e+06 ! 02 2 8.47599e+09 8e+06 1 8e+06 ! 03 3 8.79099e+09 8e+06 1 8e+06 ! 04 4 8.89599e+09 8e+06 1 8e+06 ! ! Polarization(s): RR ! ! Read 79 lines of history. ! ! Reading 9860 visibilities. select rr, 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16 ! Restricting channel ranges to the available 4 channels. ! Selecting polarization: RR, channels: 1..4 ! Reading IF 1 channels: 1..1 ! Reading IF 2 channels: 2..2 ! Reading IF 3 channels: 3..3 ! Reading IF 4 channels: 4..4 print "field_size =", field_size ! field_size = 1024 print "field_cell =", field_cell ! field_cell = 0.2 print "taper_size =", taper_size ! taper_size = 70 ![@/opt64/bin/pima_mupet_01.dfm J0927-2034_X] float lim_self lim_self = 120.0 float lim_val lim_va = 1.2 integer clean_niter clean_niter = 100 float clean_gain clean_gain = 0.03 float dynam dynam = 6.0 float soltime1 soltime1 = 120 float soltime2 soltime2 = 20 float thresh thresh = 0.5 float win_mult win_mult = 1.8 float time_av time_av = 16 float old_peak float new_peak float flux_cutoff print "===============================================================" ! =============================================================== ! print "=== Difmap script: pima_mupet_01.dvm version of 2016.05.19 === " ! === Difmap script: pima_mupet_01.dvm version of 2016.05.19 === ! mapsize field_size, field_cell ! Map grid = 1024x1024 pixels with 0.200x0.200 milli-arcsec cellsize. startmod ! Applying default point source starting model. ! Performing phase self-cal ! Adding 1 model components to the UV plane model. ! The established model now contains 1 components and 1 Jy ! ! Correcting IF 1. ! A total of 297 telescope corrections were flagged in sub-array 1. ! A total of 60 telescope corrections were flagged in sub-array 2. ! A total of 21 telescope corrections were flagged in sub-array 3. ! A total of 18 telescope corrections were flagged in sub-array 4. ! A total of 18 telescope corrections were flagged in sub-array 5. ! A total of 8 telescope corrections were flagged in sub-array 6. ! A total of 34 telescope corrections were flagged in sub-array 7. ! A total of 8 telescope corrections were flagged in sub-array 8. ! A total of 18 telescope corrections were flagged in sub-array 9. ! A total of 6 telescope corrections were flagged in sub-array 10. ! A total of 16 telescope corrections were flagged in sub-array 11. ! A total of 18 telescope corrections were flagged in sub-array 12. ! A total of 9 telescope corrections were flagged in sub-array 13. ! ! Correcting IF 2. ! A total of 297 telescope corrections were flagged in sub-array 1. ! A total of 60 telescope corrections were flagged in sub-array 2. ! A total of 21 telescope corrections were flagged in sub-array 3. ! A total of 18 telescope corrections were flagged in sub-array 4. ! A total of 18 telescope corrections were flagged in sub-array 5. ! A total of 8 telescope corrections were flagged in sub-array 6. ! A total of 34 telescope corrections were flagged in sub-array 7. ! A total of 8 telescope corrections were flagged in sub-array 8. ! A total of 18 telescope corrections were flagged in sub-array 9. ! A total of 6 telescope corrections were flagged in sub-array 10. ! A total of 16 telescope corrections were flagged in sub-array 11. ! A total of 18 telescope corrections were flagged in sub-array 12. ! A total of 9 telescope corrections were flagged in sub-array 13. ! ! Correcting IF 3. ! A total of 297 telescope corrections were flagged in sub-array 1. ! A total of 60 telescope corrections were flagged in sub-array 2. ! A total of 21 telescope corrections were flagged in sub-array 3. ! A total of 18 telescope corrections were flagged in sub-array 4. ! A total of 18 telescope corrections were flagged in sub-array 5. ! A total of 8 telescope corrections were flagged in sub-array 6. ! A total of 34 telescope corrections were flagged in sub-array 7. ! A total of 8 telescope corrections were flagged in sub-array 8. ! A total of 18 telescope corrections were flagged in sub-array 9. ! A total of 6 telescope corrections were flagged in sub-array 10. ! A total of 16 telescope corrections were flagged in sub-array 11. ! A total of 18 telescope corrections were flagged in sub-array 12. ! A total of 9 telescope corrections were flagged in sub-array 13. ! ! Correcting IF 4. ! A total of 297 telescope corrections were flagged in sub-array 1. ! A total of 60 telescope corrections were flagged in sub-array 2. ! A total of 21 telescope corrections were flagged in sub-array 3. ! A total of 18 telescope corrections were flagged in sub-array 4. ! A total of 18 telescope corrections were flagged in sub-array 5. ! A total of 8 telescope corrections were flagged in sub-array 6. ! A total of 34 telescope corrections were flagged in sub-array 7. ! A total of 8 telescope corrections were flagged in sub-array 8. ! A total of 18 telescope corrections were flagged in sub-array 9. ! A total of 6 telescope corrections were flagged in sub-array 10. ! A total of 16 telescope corrections were flagged in sub-array 11. ! A total of 18 telescope corrections were flagged in sub-array 12. ! A total of 9 telescope corrections were flagged in sub-array 13. ! ! Fit before self-cal, rms=1.771386Jy sigma=18.503381 ! Fit after self-cal, rms=0.506279Jy sigma=5.043477 ! clrmod: Cleared the established, tentative and continuum models. ! Redundant starting model cleared. uvw 2,-1 ! Uniform weighting binwidth: 2 (pixels). ! Gridding weights will be scaled by errors raised to the power -1. ! Radial weighting is not currently selected. flux_cutoff = imstat(rms) * dynam ! Inverting map and beam ! Your choice of large map pixels excluded 0.728% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=0.713 mas, bmaj=2.024 mas, bpa=-6.48 degrees ! Estimated noise=1.07372 mJy/beam. repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! Added new window around map position (0, 0). ! clean: niter=100 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 1.06499 Jy ! Component: 100 - total flux cleaned = 1.32061 Jy ! Total flux subtracted in 100 components = 1.32061 Jy ! Clean residual min=-0.029706 max=0.096399 Jy/beam ! Clean residual mean=0.000480 rms=0.006551 Jy/beam ! Combined flux in latest and established models = 1.32061 Jy ! Performing phase self-cal ! Adding 5 model components to the UV plane model. ! The established model now contains 5 components and 1.32061 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.277413Jy sigma=2.542995 ! Fit after self-cal, rms=0.277363Jy sigma=2.542578 ! Inverting map ! Your choice of large map pixels excluded 0.728% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! clean: niter=100 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.0978936 Jy ! Component: 100 - total flux cleaned = 0.14293 Jy ! Total flux subtracted in 100 components = 0.14293 Jy ! Clean residual min=-0.021354 max=0.030744 Jy/beam ! Clean residual mean=0.000334 rms=0.004032 Jy/beam ! Combined flux in latest and established models = 1.46354 Jy ! Performing phase self-cal ! Adding 22 model components to the UV plane model. ! The established model now contains 24 components and 1.46354 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.227605Jy sigma=1.996530 ! Fit after self-cal, rms=0.227363Jy sigma=1.994346 ! Inverting map ! Your choice of large map pixels excluded 0.728% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Added new window around map position (-2.2, -0.8). ! clean: niter=100 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.0207902 Jy ! Component: 100 - total flux cleaned = 0.0270381 Jy ! Total flux subtracted in 100 components = 0.0270381 Jy ! Clean residual min=-0.018656 max=0.025065 Jy/beam ! Clean residual mean=0.000306 rms=0.003582 Jy/beam ! Combined flux in latest and established models = 1.49058 Jy ! Performing phase self-cal ! Adding 11 model components to the UV plane model. ! The established model now contains 32 components and 1.49058 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.221590Jy sigma=1.940687 ! Fit after self-cal, rms=0.221367Jy sigma=1.938311 ! Inverting map ! Your choice of large map pixels excluded 0.728% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Added new window around map position (-1, -4.2). ! clean: niter=100 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.0157047 Jy ! Component: 100 - total flux cleaned = 0.0199871 Jy ! Total flux subtracted in 100 components = 0.0199871 Jy ! Clean residual min=-0.018136 max=0.022058 Jy/beam ! Clean residual mean=0.000284 rms=0.003326 Jy/beam ! Combined flux in latest and established models = 1.51057 Jy ! Performing phase self-cal ! Adding 17 model components to the UV plane model. ! The established model now contains 40 components and 1.51057 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.218288Jy sigma=1.915418 ! Fit after self-cal, rms=0.218202Jy sigma=1.912601 ! Inverting map ! Your choice of large map pixels excluded 0.728% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec print "============== Finished uniform weighting clean ===============" ! ============== Finished uniform weighting clean =============== ! uvw 0,-1 ! Uniform weighting is not currently selected. ! Gridding weights will be scaled by errors raised to the power -1. ! Radial weighting is not currently selected. win_mult = win_mult * 1.6 clean_niter = clean_niter * 2 dynam = dynam - 0.5 flux_cutoff = imstat(rms) * dynam ! Inverting map and beam ! Your choice of large map pixels excluded 0.728% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=0.9902 mas, bmaj=2.662 mas, bpa=-6.424 degrees ! Estimated noise=0.794864 mJy/beam. repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! Added new window around map position (-1, 3.6). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.0265238 Jy ! Component: 100 - total flux cleaned = 0.0436242 Jy ! Component: 150 - total flux cleaned = 0.0556591 Jy ! Component: 200 - total flux cleaned = 0.0608429 Jy ! Total flux subtracted in 200 components = 0.0608429 Jy ! Clean residual min=-0.009953 max=0.017015 Jy/beam ! Clean residual mean=0.001687 rms=0.003320 Jy/beam ! Combined flux in latest and established models = 1.57141 Jy ! Performing phase self-cal ! Adding 19 model components to the UV plane model. ! The established model now contains 56 components and 1.57141 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.213160Jy sigma=1.876258 ! Fit after self-cal, rms=0.212921Jy sigma=1.872207 ! Inverting map ! Your choice of large map pixels excluded 0.728% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec print "============== Finished natural weighting clean ==============" ! ============== Finished natural weighting clean ============== ! restore ! restore: Substituting estimate of restoring beam from last 'invert'. ! Restoring with beam: 0.9902 x 2.662 at -6.424 degrees (North through East) ! Clean map min=-0.0092857 max=1.3906 Jy/beam gscale true ! Performing overall amplitude self-cal ! ! Correcting IF 1. ! A total of 612 telescope corrections were flagged in sub-array 1. ! Telescope amplitude corrections in sub-array 1: ! MA 0.00* ON 0.00* WZ 0.00* ! ! A total of 48 telescope corrections were flagged in sub-array 2. ! Telescope amplitude corrections in sub-array 2: ! MA 0.94 ON 1.02 SC 1.06 WZ 0.94 ! ! A total of 18 telescope corrections were flagged in sub-array 3. ! Telescope amplitude corrections in sub-array 3: ! SC 0.00* WF 0.00* WZ 0.00* ! ! A total of 45 telescope corrections were flagged in sub-array 4. ! Telescope amplitude corrections in sub-array 4: ! MA 0.00* WF 0.00* WZ 0.00* ! ! Telescope amplitude corrections in sub-array 5: ! HN 0.00* WF 0.00* ! ! Telescope amplitude corrections in sub-array 6: ! FD 1.04 KP 1.02 LA 1.01 MA 1.13 ! ! Telescope amplitude corrections in sub-array 7: ! FD 0.98 HN 1.05 KP 1.00 LA 1.01 ! NL 1.02 PT 1.02 SC 1.04 WF 0.90 ! ! Telescope amplitude corrections in sub-array 8: ! HN 0.97 NL 1.08 SC 1.02 WF 0.87 ! ! Telescope amplitude corrections in sub-array 9: ! FD 0.98 HN 1.05 KP 0.99 LA 0.98 ! MK 1.02 NL 1.07 PT 1.02 SC 1.03 ! WF 0.90 ! ! A total of 21 telescope corrections were flagged in sub-array 10. ! Telescope amplitude corrections in sub-array 10: ! HN 0.00* SC 0.00* WF 0.00* ! ! Telescope amplitude corrections in sub-array 11: ! FD 0.98 HN 1.25 KP 1.00 LA 0.98 ! MK 1.01 PT 1.01 SC 1.00 WF 0.95 ! ! Telescope amplitude corrections in sub-array 12: ! LA 0.00* PT 0.00* ! ! A total of 18 telescope corrections were flagged in sub-array 13. ! Telescope amplitude corrections in sub-array 13: ! FD 0.00* MK 0.00* PT 0.00* ! ! ! Correcting IF 2. ! A total of 612 telescope corrections were flagged in sub-array 1. ! Telescope amplitude corrections in sub-array 1: ! MA 0.00* ON 0.00* WZ 0.00* ! ! A total of 48 telescope corrections were flagged in sub-array 2. ! Telescope amplitude corrections in sub-array 2: ! MA 0.98 ON 1.06 SC 1.09 WZ 0.93 ! ! A total of 18 telescope corrections were flagged in sub-array 3. ! Telescope amplitude corrections in sub-array 3: ! SC 0.00* WF 0.00* WZ 0.00* ! ! A total of 45 telescope corrections were flagged in sub-array 4. ! Telescope amplitude corrections in sub-array 4: ! MA 0.00* WF 0.00* WZ 0.00* ! ! Telescope amplitude corrections in sub-array 5: ! HN 0.00* WF 0.00* ! ! Telescope amplitude corrections in sub-array 6: ! FD 0.98 KP 1.03 LA 0.98 MA 1.13 ! ! Telescope amplitude corrections in sub-array 7: ! FD 0.99 HN 1.03 KP 0.98 LA 1.00 ! NL 0.99 PT 1.03 SC 1.01 WF 0.91 ! ! Telescope amplitude corrections in sub-array 8: ! HN 0.95 NL 1.02 SC 1.03 WF 0.89 ! ! Telescope amplitude corrections in sub-array 9: ! FD 1.00 HN 1.05 KP 0.98 LA 0.99 ! MK 1.00 NL 1.03 PT 1.01 SC 0.99 ! WF 0.90 ! ! A total of 21 telescope corrections were flagged in sub-array 10. ! Telescope amplitude corrections in sub-array 10: ! HN 0.00* SC 0.00* WF 0.00* ! ! Telescope amplitude corrections in sub-array 11: ! FD 0.98 HN 1.27 KP 1.01 LA 1.00 ! MK 0.98 PT 1.02 SC 1.01 WF 0.93 ! ! Telescope amplitude corrections in sub-array 12: ! LA 0.00* PT 0.00* ! ! A total of 18 telescope corrections were flagged in sub-array 13. ! Telescope amplitude corrections in sub-array 13: ! FD 0.00* MK 0.00* PT 0.00* ! ! ! Correcting IF 3. ! A total of 612 telescope corrections were flagged in sub-array 1. ! Telescope amplitude corrections in sub-array 1: ! MA 0.00* ON 0.00* WZ 0.00* ! ! A total of 48 telescope corrections were flagged in sub-array 2. ! Telescope amplitude corrections in sub-array 2: ! MA 1.03 ON 1.07 SC 1.00 WZ 0.96 ! ! A total of 18 telescope corrections were flagged in sub-array 3. ! Telescope amplitude corrections in sub-array 3: ! SC 0.00* WF 0.00* WZ 0.00* ! ! A total of 45 telescope corrections were flagged in sub-array 4. ! Telescope amplitude corrections in sub-array 4: ! MA 0.00* WF 0.00* WZ 0.00* ! ! Telescope amplitude corrections in sub-array 5: ! HN 0.00* WF 0.00* ! ! Telescope amplitude corrections in sub-array 6: ! FD 1.02 KP 1.02 LA 0.95 MA 1.29 ! ! Telescope amplitude corrections in sub-array 7: ! FD 0.99 HN 0.99 KP 1.00 LA 1.00 ! NL 1.00 PT 1.02 SC 0.99 WF 0.88 ! ! Telescope amplitude corrections in sub-array 8: ! HN 0.96 NL 1.05 SC 1.04 WF 0.86 ! ! Telescope amplitude corrections in sub-array 9: ! FD 0.97 HN 1.03 KP 0.99 LA 0.99 ! MK 0.98 NL 1.03 PT 1.03 SC 1.01 ! WF 0.88 ! ! A total of 21 telescope corrections were flagged in sub-array 10. ! Telescope amplitude corrections in sub-array 10: ! HN 0.00* SC 0.00* WF 0.00* ! ! Telescope amplitude corrections in sub-array 11: ! FD 0.97 HN 1.17 KP 0.99 LA 0.98 ! MK 0.99 PT 1.02 SC 1.02 WF 0.94 ! ! Telescope amplitude corrections in sub-array 12: ! LA 0.00* PT 0.00* ! ! A total of 18 telescope corrections were flagged in sub-array 13. ! Telescope amplitude corrections in sub-array 13: ! FD 0.00* MK 0.00* PT 0.00* ! ! ! Correcting IF 4. ! A total of 612 telescope corrections were flagged in sub-array 1. ! Telescope amplitude corrections in sub-array 1: ! MA 0.00* ON 0.00* WZ 0.00* ! ! A total of 48 telescope corrections were flagged in sub-array 2. ! Telescope amplitude corrections in sub-array 2: ! MA 1.03 ON 1.06 SC 0.99 WZ 0.99 ! ! A total of 18 telescope corrections were flagged in sub-array 3. ! Telescope amplitude corrections in sub-array 3: ! SC 0.00* WF 0.00* WZ 0.00* ! ! A total of 45 telescope corrections were flagged in sub-array 4. ! Telescope amplitude corrections in sub-array 4: ! MA 0.00* WF 0.00* WZ 0.00* ! ! Telescope amplitude corrections in sub-array 5: ! HN 0.00* WF 0.00* ! ! Telescope amplitude corrections in sub-array 6: ! FD 0.99 KP 0.98 LA 0.97 MA 1.44 ! ! Telescope amplitude corrections in sub-array 7: ! FD 0.98 HN 1.01 KP 0.98 LA 0.99 ! NL 1.03 PT 1.00 SC 0.99 WF 0.88 ! ! Telescope amplitude corrections in sub-array 8: ! HN 0.94 NL 1.05 SC 0.98 WF 0.87 ! ! Telescope amplitude corrections in sub-array 9: ! FD 1.00 HN 1.02 KP 0.97 LA 0.98 ! MK 0.99 NL 1.05 PT 1.01 SC 0.98 ! WF 0.90 ! ! A total of 21 telescope corrections were flagged in sub-array 10. ! Telescope amplitude corrections in sub-array 10: ! HN 0.00* SC 0.00* WF 0.00* ! ! Telescope amplitude corrections in sub-array 11: ! FD 0.99 HN 1.11 KP 1.00 LA 0.99 ! MK 0.99 PT 1.00 SC 1.03 WF 0.90 ! ! Telescope amplitude corrections in sub-array 12: ! LA 0.00* PT 0.00* ! ! A total of 18 telescope corrections were flagged in sub-array 13. ! Telescope amplitude corrections in sub-array 13: ! FD 0.00* MK 0.00* PT 0.00* ! ! ! Fit before self-cal, rms=0.212921Jy sigma=1.872207 ! Fit after self-cal, rms=0.151915Jy sigma=1.492145 dynam = dynam - 0.5 flux_cutoff = imstat(rms) * dynam ! Inverting map and beam ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=0.8586 mas, bmaj=2.328 mas, bpa=-7.017 degrees ! Estimated noise=0.93968 mJy/beam. repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00352552 Jy ! Component: 100 - total flux cleaned = 0.00663469 Jy ! Component: 150 - total flux cleaned = 0.00829815 Jy ! Component: 200 - total flux cleaned = 0.00961551 Jy ! Total flux subtracted in 200 components = 0.00961551 Jy ! Clean residual min=-0.007507 max=0.007132 Jy/beam ! Clean residual mean=0.000611 rms=0.001726 Jy/beam ! Combined flux in latest and established models = 1.58102 Jy ! Performing phase self-cal ! Adding 28 model components to the UV plane model. ! The established model now contains 81 components and 1.58102 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.150940Jy sigma=1.480752 ! Fit after self-cal, rms=0.150869Jy sigma=1.479547 ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec selfcal true, true, soltime1 ! Performing amp+phase self-cal over 120 minute time intervals ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.150869Jy sigma=1.479547 ! Fit after self-cal, rms=0.150166Jy sigma=1.471167 dynam = dynam - 0.75 clean clean_niter,clean_gain ! Inverting map and beam ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=0.8582 mas, bmaj=2.328 mas, bpa=-7.004 degrees ! Estimated noise=0.940129 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = -0.000160966 Jy ! Component: 100 - total flux cleaned = 0.00101839 Jy ! Component: 150 - total flux cleaned = 0.00222856 Jy ! Component: 200 - total flux cleaned = 0.00234631 Jy ! Total flux subtracted in 200 components = 0.00234631 Jy ! Clean residual min=-0.007501 max=0.006835 Jy/beam ! Clean residual mean=0.000491 rms=0.001553 Jy/beam ! Combined flux in latest and established models = 1.58337 Jy selfcal ! Performing phase self-cal ! Adding 25 model components to the UV plane model. ! The established model now contains 92 components and 1.58337 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.149801Jy sigma=1.466775 ! Fit after self-cal, rms=0.149783Jy sigma=1.466482 flux_cutoff = imstat(rms) * dynam ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = -0.000532025 Jy ! Component: 100 - total flux cleaned = -0.000421608 Jy ! Component: 150 - total flux cleaned = -0.00042144 Jy ! Component: 200 - total flux cleaned = -0.000423886 Jy ! Total flux subtracted in 200 components = -0.000423886 Jy ! Clean residual min=-0.007278 max=0.006830 Jy/beam ! Clean residual mean=0.000496 rms=0.001534 Jy/beam ! Combined flux in latest and established models = 1.58295 Jy ! Performing phase self-cal ! Adding 30 model components to the UV plane model. ! The established model now contains 106 components and 1.58295 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.149657Jy sigma=1.464930 ! Fit after self-cal, rms=0.149656Jy sigma=1.464826 ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec selfcal true, true, soltime2 ! Performing amp+phase self-cal over 20 minute time intervals ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.149656Jy sigma=1.464826 ! Fit after self-cal, rms=0.148439Jy sigma=1.451130 clean clean_niter,clean_gain ! Inverting map and beam ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=0.8581 mas, bmaj=2.329 mas, bpa=-6.997 degrees ! Estimated noise=0.940515 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.000560108 Jy ! Component: 100 - total flux cleaned = 0.000803825 Jy ! Component: 150 - total flux cleaned = 0.000906208 Jy ! Component: 200 - total flux cleaned = 0.000904072 Jy ! Total flux subtracted in 200 components = 0.000904072 Jy ! Clean residual min=-0.005204 max=0.005701 Jy/beam ! Clean residual mean=0.000390 rms=0.001309 Jy/beam ! Combined flux in latest and established models = 1.58385 Jy selfcal ! Performing phase self-cal ! Adding 29 model components to the UV plane model. ! The established model now contains 120 components and 1.58385 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.148272Jy sigma=1.449211 ! Fit after self-cal, rms=0.148266Jy sigma=1.449102 flux_cutoff = imstat(rms) * dynam ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! Added new window around map position (-2.8, 34.8). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00493978 Jy ! Component: 100 - total flux cleaned = 0.00699505 Jy ! Component: 150 - total flux cleaned = 0.00773176 Jy ! Component: 200 - total flux cleaned = 0.00813587 Jy ! Total flux subtracted in 200 components = 0.00813587 Jy ! Clean residual min=-0.004830 max=0.005235 Jy/beam ! Clean residual mean=0.000306 rms=0.001247 Jy/beam ! Combined flux in latest and established models = 1.59199 Jy ! Performing phase self-cal ! Adding 29 model components to the UV plane model. ! The established model now contains 136 components and 1.59199 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.148056Jy sigma=1.446695 ! Fit after self-cal, rms=0.148051Jy sigma=1.446505 ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec uvtaper 0.3,taper_size ! Gaussian taper: value 0.3 at UV radius = 70 mega-wavelengths. win_mult = win_mult * 1.2 selfcal true, true, soltime2 ! Performing amp+phase self-cal over 20 minute time intervals ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.148051Jy sigma=1.446505 ! Fit after self-cal, rms=0.147950Jy sigma=1.446059 clean clean_niter,clean_gain ! Inverting map and beam ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=1.958 mas, bmaj=3.69 mas, bpa=-7.751 degrees ! Estimated noise=1.2409 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00200138 Jy ! Component: 100 - total flux cleaned = 0.00226781 Jy ! Component: 150 - total flux cleaned = 0.0025578 Jy ! Component: 200 - total flux cleaned = 0.00274809 Jy ! Total flux subtracted in 200 components = 0.00274809 Jy ! Clean residual min=-0.004881 max=0.006268 Jy/beam ! Clean residual mean=0.000548 rms=0.001505 Jy/beam ! Combined flux in latest and established models = 1.59473 Jy selfcal ! Performing phase self-cal ! Adding 26 model components to the UV plane model. ! The established model now contains 158 components and 1.59473 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.147895Jy sigma=1.445251 ! Fit after self-cal, rms=0.147887Jy sigma=1.445178 flux_cutoff = imstat(rms) * dynam ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.000270341 Jy ! Component: 100 - total flux cleaned = 0.000552116 Jy ! Component: 150 - total flux cleaned = 0.000702007 Jy ! Component: 200 - total flux cleaned = 0.000836745 Jy ! Total flux subtracted in 200 components = 0.000836745 Jy ! Clean residual min=-0.004748 max=0.006113 Jy/beam ! Clean residual mean=0.000529 rms=0.001482 Jy/beam ! Combined flux in latest and established models = 1.59557 Jy ! Performing phase self-cal ! Adding 27 model components to the UV plane model. ! The established model now contains 169 components and 1.59557 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.147864Jy sigma=1.444914 ! Fit after self-cal, rms=0.147859Jy sigma=1.444888 ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec uvtaper 0,0 ! No UV-taper is currently set. win_mult = win_mult / 1.2 print "============== Finished amplitude self-cal ==============" ! ============== Finished amplitude self-cal ============== restore ! Inverting map and beam ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=0.8581 mas, bmaj=2.329 mas, bpa=-6.996 degrees ! Estimated noise=0.940447 mJy/beam. ! restore: Substituting estimate of restoring beam from last 'invert'. ! Restoring with beam: 0.8581 x 2.329 at -6.996 degrees (North through East) ! Clean map min=-0.0041744 max=1.3691 Jy/beam if(peak(flux) > thresh) selfcal true, true clean clean_niter,clean_gain selfcal flux_cutoff = imstat(rms) * dynam repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam selfcal new_peak = peak(flux) until(new_peak<=flux_cutoff) selfcal true, true end if ! Performing amp+phase self-cal ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.147859Jy sigma=1.444888 ! Fit after self-cal, rms=0.135328Jy sigma=1.289481 ! Inverting map and beam ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=0.8579 mas, bmaj=2.33 mas, bpa=-7.001 degrees ! Estimated noise=0.940362 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = -0.00109791 Jy ! Component: 100 - total flux cleaned = -0.00133807 Jy ! Component: 150 - total flux cleaned = -0.00155399 Jy ! Component: 200 - total flux cleaned = -0.00168806 Jy ! Total flux subtracted in 200 components = -0.00168806 Jy ! Clean residual min=-0.004570 max=0.004918 Jy/beam ! Clean residual mean=0.000173 rms=0.001181 Jy/beam ! Combined flux in latest and established models = 1.59388 Jy ! Performing phase self-cal ! Adding 32 model components to the UV plane model. ! The established model now contains 183 components and 1.59388 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.135241Jy sigma=1.288452 ! Fit after self-cal, rms=0.135243Jy sigma=1.288410 ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = -0.000372708 Jy ! Component: 100 - total flux cleaned = -0.000372823 Jy ! Component: 150 - total flux cleaned = -0.000374614 Jy ! Component: 200 - total flux cleaned = -0.000487349 Jy ! Total flux subtracted in 200 components = -0.000487349 Jy ! Clean residual min=-0.004573 max=0.004859 Jy/beam ! Clean residual mean=0.000179 rms=0.001176 Jy/beam ! Combined flux in latest and established models = 1.5934 Jy ! Performing phase self-cal ! Adding 34 model components to the UV plane model. ! The established model now contains 190 components and 1.5934 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.135189Jy sigma=1.287830 ! Fit after self-cal, rms=0.135192Jy sigma=1.287808 ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Performing amp+phase self-cal ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.135192Jy sigma=1.287808 ! Fit after self-cal, rms=0.135108Jy sigma=1.287637 print "============== Clearing model and starting over ==========" ! ============== Clearing model and starting over ========== clrmod true ! clrmod: Cleared the established and tentative models. uvw 2,-1 ! Uniform weighting binwidth: 2 (pixels). ! Gridding weights will be scaled by errors raised to the power -1. ! Radial weighting is not currently selected. clean clean_niter,clean_gain ! Inverting map and beam ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=0.7152 mas, bmaj=1.985 mas, bpa=-6.462 degrees ! Estimated noise=1.14858 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 1.06356 Jy ! Component: 100 - total flux cleaned = 1.32089 Jy ! Component: 150 - total flux cleaned = 1.4189 Jy ! Component: 200 - total flux cleaned = 1.46413 Jy ! Total flux subtracted in 200 components = 1.46413 Jy ! Clean residual min=-0.009574 max=0.021492 Jy/beam ! Clean residual mean=0.000210 rms=0.002568 Jy/beam ! Combined flux in latest and established models = 1.46413 Jy uvw 0,-1 ! Uniform weighting is not currently selected. ! Gridding weights will be scaled by errors raised to the power -1. ! Radial weighting is not currently selected. flux_cutoff = imstat(rms) * dynam ! Adding 26 model components to the UV plane model. ! The established model now contains 26 components and 1.46413 Jy ! Inverting map and beam ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=0.8579 mas, bmaj=2.33 mas, bpa=-7 degrees ! Estimated noise=0.940172 mJy/beam. repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam keep new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.0369814 Jy ! Component: 100 - total flux cleaned = 0.0596618 Jy ! Component: 150 - total flux cleaned = 0.0749877 Jy ! Component: 200 - total flux cleaned = 0.0860396 Jy ! Total flux subtracted in 200 components = 0.0860396 Jy ! Clean residual min=-0.005360 max=0.007201 Jy/beam ! Clean residual mean=0.000664 rms=0.001522 Jy/beam ! Combined flux in latest and established models = 1.55017 Jy ! Adding 46 model components to the UV plane model. ! The established model now contains 65 components and 1.55017 Jy ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Added new window around map position (2.8, -1.2). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00867412 Jy ! Component: 100 - total flux cleaned = 0.015475 Jy ! Component: 150 - total flux cleaned = 0.0210909 Jy ! Component: 200 - total flux cleaned = 0.0256388 Jy ! Total flux subtracted in 200 components = 0.0256388 Jy ! Clean residual min=-0.004709 max=0.005417 Jy/beam ! Clean residual mean=0.000343 rms=0.001273 Jy/beam ! Combined flux in latest and established models = 1.57581 Jy ! Adding 38 model components to the UV plane model. ! The established model now contains 93 components and 1.57581 Jy ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Added new window around map position (2.8, 13). ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00454223 Jy ! Component: 100 - total flux cleaned = 0.00684155 Jy ! Component: 150 - total flux cleaned = 0.00849899 Jy ! Component: 200 - total flux cleaned = 0.00988506 Jy ! Total flux subtracted in 200 components = 0.00988506 Jy ! Clean residual min=-0.004378 max=0.005017 Jy/beam ! Clean residual mean=0.000220 rms=0.001196 Jy/beam ! Combined flux in latest and established models = 1.58569 Jy ! Adding 38 model components to the UV plane model. ! The established model now contains 109 components and 1.58569 Jy ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec uvtaper 0.3,taper_size ! Gaussian taper: value 0.3 at UV radius = 70 mega-wavelengths. clean clean_niter,clean_gain ! Inverting map and beam ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=1.958 mas, bmaj=3.689 mas, bpa=-7.761 degrees ! Estimated noise=1.2409 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.00405735 Jy ! Component: 100 - total flux cleaned = 0.00627901 Jy ! Component: 150 - total flux cleaned = 0.00723919 Jy ! Component: 200 - total flux cleaned = 0.00797954 Jy ! Total flux subtracted in 200 components = 0.00797954 Jy ! Clean residual min=-0.004530 max=0.005115 Jy/beam ! Clean residual mean=0.000290 rms=0.001314 Jy/beam ! Combined flux in latest and established models = 1.59367 Jy flux_cutoff = imstat(rms) * dynam repeat if (peak(flux) > flux_cutoff) peakwin win_mult clean clean_niter,clean_gain flux_cutoff = imstat(rms) * dynam keep new_peak = peak(flux) until(new_peak<=flux_cutoff) ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = 0.000574359 Jy ! Component: 100 - total flux cleaned = 0.000766827 Jy ! Component: 150 - total flux cleaned = 0.00094847 Jy ! Component: 200 - total flux cleaned = 0.00111732 Jy ! Total flux subtracted in 200 components = 0.00111732 Jy ! Clean residual min=-0.004465 max=0.004984 Jy/beam ! Clean residual mean=0.000261 rms=0.001297 Jy/beam ! Combined flux in latest and established models = 1.59479 Jy ! Adding 31 model components to the UV plane model. ! The established model now contains 132 components and 1.59479 Jy ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec uvtaper 0,0 ! No UV-taper is currently set. clean ! Inverting map and beam ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! Estimated beam: bmin=0.8579 mas, bmaj=2.33 mas, bpa=-7 degrees ! Estimated noise=0.940172 mJy/beam. ! clean: niter=200 gain=0.03 cutoff=0 ! Component: 050 - total flux cleaned = -0.000996934 Jy ! Component: 100 - total flux cleaned = -0.00069278 Jy ! Component: 150 - total flux cleaned = -0.000597272 Jy ! Component: 200 - total flux cleaned = -0.000595371 Jy ! Total flux subtracted in 200 components = -0.000595371 Jy ! Clean residual min=-0.004281 max=0.004557 Jy/beam ! Clean residual mean=0.000119 rms=0.001126 Jy/beam ! Combined flux in latest and established models = 1.59419 Jy selfcal ! Performing phase self-cal ! Adding 25 model components to the UV plane model. ! The established model now contains 148 components and 1.59419 Jy ! ! Correcting IF 1. ! ! Correcting IF 2. ! ! Correcting IF 3. ! ! Correcting IF 4. ! ! Fit before self-cal, rms=0.135115Jy sigma=1.287084 ! Fit after self-cal, rms=0.135017Jy sigma=1.286174 wmodel J0927-2034_X_map.mod ! Writing 148 model components to file: J0927-2034_X_map.mod wobs J0927-2034_X_uvs.fits ! Writing UV FITS file: J0927-2034_X_uvs.fits wwins J0927-2034_X_map.win ! wwins: Wrote 7 windows to J0927-2034_X_map.win x = (field_size-8) * field_cell / 4 addwin -x,x,-x,x clean (field_size*4),0.01 ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! clean: niter=4096 gain=0.01 cutoff=0 ! Component: 050 - total flux cleaned = 0.00131378 Jy ! Component: 100 - total flux cleaned = 0.00162833 Jy ! Component: 150 - total flux cleaned = 0.00192967 Jy ! Component: 200 - total flux cleaned = 0.00200384 Jy ! Component: 250 - total flux cleaned = 0.00243682 Jy ! Component: 300 - total flux cleaned = 0.00257719 Jy ! Component: 350 - total flux cleaned = 0.0027842 Jy ! Component: 400 - total flux cleaned = 0.00305663 Jy ! Component: 450 - total flux cleaned = 0.00319083 Jy ! Component: 500 - total flux cleaned = 0.00332414 Jy ! Component: 550 - total flux cleaned = 0.00332412 Jy ! Component: 600 - total flux cleaned = 0.00326001 Jy ! Component: 650 - total flux cleaned = 0.00345096 Jy ! Component: 700 - total flux cleaned = 0.00357588 Jy ! Component: 750 - total flux cleaned = 0.00351326 Jy ! Component: 800 - total flux cleaned = 0.00351393 Jy ! Component: 850 - total flux cleaned = 0.00357439 Jy ! Component: 900 - total flux cleaned = 0.00369443 Jy ! Component: 950 - total flux cleaned = 0.00393085 Jy ! Component: 1000 - total flux cleaned = 0.00410577 Jy ! Component: 1050 - total flux cleaned = 0.00416347 Jy ! Component: 1100 - total flux cleaned = 0.00445112 Jy ! Component: 1150 - total flux cleaned = 0.00445096 Jy ! Component: 1200 - total flux cleaned = 0.00484636 Jy ! Component: 1250 - total flux cleaned = 0.00479128 Jy ! Component: 1300 - total flux cleaned = 0.00501276 Jy ! Component: 1350 - total flux cleaned = 0.00534229 Jy ! Component: 1400 - total flux cleaned = 0.00545058 Jy ! Component: 1450 - total flux cleaned = 0.00577404 Jy ! Component: 1500 - total flux cleaned = 0.00609614 Jy ! Component: 1550 - total flux cleaned = 0.00636161 Jy ! Component: 1600 - total flux cleaned = 0.0066255 Jy ! Component: 1650 - total flux cleaned = 0.00699194 Jy ! Component: 1700 - total flux cleaned = 0.00699182 Jy ! Component: 1750 - total flux cleaned = 0.00735254 Jy ! Component: 1800 - total flux cleaned = 0.0075061 Jy ! Component: 1850 - total flux cleaned = 0.00745505 Jy ! Component: 1900 - total flux cleaned = 0.00775831 Jy ! Component: 1950 - total flux cleaned = 0.00795853 Jy ! Component: 2000 - total flux cleaned = 0.00815796 Jy ! Component: 2050 - total flux cleaned = 0.00815766 Jy ! Component: 2100 - total flux cleaned = 0.008305 Jy ! Component: 2150 - total flux cleaned = 0.00850002 Jy ! Component: 2200 - total flux cleaned = 0.0086453 Jy ! Component: 2250 - total flux cleaned = 0.00864509 Jy ! Component: 2300 - total flux cleaned = 0.00874131 Jy ! Component: 2350 - total flux cleaned = 0.00869339 Jy ! Component: 2400 - total flux cleaned = 0.00897693 Jy ! Component: 2450 - total flux cleaned = 0.00897705 Jy ! Component: 2500 - total flux cleaned = 0.00925738 Jy ! Component: 2550 - total flux cleaned = 0.00934979 Jy ! Component: 2600 - total flux cleaned = 0.00944213 Jy ! Component: 2650 - total flux cleaned = 0.0095796 Jy ! Component: 2700 - total flux cleaned = 0.00967068 Jy ! Component: 2750 - total flux cleaned = 0.0097613 Jy ! Component: 2800 - total flux cleaned = 0.00998627 Jy ! Component: 2850 - total flux cleaned = 0.00994127 Jy ! Component: 2900 - total flux cleaned = 0.010075 Jy ! Component: 2950 - total flux cleaned = 0.0102081 Jy ! Component: 3000 - total flux cleaned = 0.0102961 Jy ! Component: 3050 - total flux cleaned = 0.010428 Jy ! Component: 3100 - total flux cleaned = 0.0106456 Jy ! Component: 3150 - total flux cleaned = 0.0106893 Jy ! Component: 3200 - total flux cleaned = 0.0107755 Jy ! Component: 3250 - total flux cleaned = 0.0109039 Jy ! Component: 3300 - total flux cleaned = 0.0109043 Jy ! Component: 3350 - total flux cleaned = 0.0110742 Jy ! Component: 3400 - total flux cleaned = 0.0112429 Jy ! Component: 3450 - total flux cleaned = 0.011243 Jy ! Component: 3500 - total flux cleaned = 0.0113681 Jy ! Component: 3550 - total flux cleaned = 0.0114926 Jy ! Component: 3600 - total flux cleaned = 0.0114103 Jy ! Component: 3650 - total flux cleaned = 0.0114925 Jy ! Component: 3700 - total flux cleaned = 0.0115741 Jy ! Component: 3750 - total flux cleaned = 0.0115742 Jy ! Component: 3800 - total flux cleaned = 0.0117361 Jy ! Component: 3850 - total flux cleaned = 0.0117765 Jy ! Component: 3900 - total flux cleaned = 0.0118165 Jy ! Component: 3950 - total flux cleaned = 0.011777 Jy ! Component: 4000 - total flux cleaned = 0.012173 Jy ! Component: 4050 - total flux cleaned = 0.0125275 Jy ! Total flux subtracted in 4096 components = 0.0123705 Jy ! Clean residual min=-0.002368 max=0.002490 Jy/beam ! Clean residual mean=0.000066 rms=0.000692 Jy/beam ! Combined flux in latest and established models = 1.60656 Jy keep ! Adding 323 model components to the UV plane model. ! The established model now contains 471 components and 1.60656 Jy ![Exited script file: /opt64/bin/pima_mupet_01.dfm] wmap /scr/pima/rv102_uvs/J0927-2034_X_map.fits ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec ! restore: Substituting estimate of restoring beam from last 'invert'. ! Restoring with beam: 0.8579 x 2.33 at -7 degrees (North through East) ! Clean map min=-0.0034136 max=1.3743 Jy/beam ! Writing clean map to FITS file: /scr/pima/rv102_uvs/J0927-2034_X_map.fits wmodel /scr/pima/rv102_uvs/J0927-2034_X_map.mod ! Writing 471 model components to file: /scr/pima/rv102_uvs/J0927-2034_X_map.mod wobs /scr/pima/rv102_uvs/J0927-2034_X_uvs.fits ! Writing UV FITS file: /scr/pima/rv102_uvs/J0927-2034_X_uvs.fits wwins /scr/pima/rv102_uvs/J0927-2034_X_map.win ! wwins: Wrote 8 windows to /scr/pima/rv102_uvs/J0927-2034_X_map.win float peak_flux peak_flux = peak(flux,max) print "The peak flux is", peak_flux ! The peak flux is 1.3743 invert ! Inverting map ! Your choice of large map pixels excluded 1.21% of the data. ! The x-axis pixel size should ideally be below 0.1866 milli-arcsec float image_rms image_rms = imstat(rms) print "The final image rms is",image_rms ! The final image rms is 0.000692115 loglevs 100*3*image_rms/peak_flux ! The new contour levels are: ! -0.151084 0.151084 0.302168 0.604337 1.20867 2.41735 4.83469 9.66939 19.3388 38.6776 77.3551 print "clev= ", int(3*image_rms*10000)/10000 ! clev= 0.002 print "peak= ", int(1000*peak_flux)/1000 ! peak= 1.374 print "dyn_range= ", int(1000*peak_flux/image_rms)/1000 ! dyn_range= 1985.65 quit ! Quitting program ! Log file /scr/pima/rv102_uvs/J0927-2034_X_dfm.log closed on Sat Nov 9 10:18:38 2019